Is the Extended straight nozzle, nickel-plated brass, series 105 compatible with other M12x1.25 threaded fittings and accessories?

Yes. The Extended straight nozzle, nickel-plated brass, series 105 uses a standard metric thread M12x1.25, so it is mechanically compatible with other fittings and accessories that share the same M12x1.25 specification. Its construction (nickel-plated brass), 5 mm tube diameter and available lengths (115, 165, 265, 415 mm) do not affect thread compatibility. However, ensure mating components are rated for the nozzleâs operating conditions (max 10 bar, -10Â°C to +50Â°C) and that internal diameters and sealing methods (e.g., O-rings, tapered vs. parallel seats) match to prevent leaks or flow restrictions.

Can the Extended straight nozzle, nickel-plated brass, series 105 withstand continuous use at 10 bar without performance loss?

Yes. The Extended straight nozzle, nickel-plated brass, series 105 is rated with a maximum pressure of 10 bar and an operating temperature range of -10Â°C to +50Â°C. Within these specified limits it is designed to withstand continuous use at 10 bar without performance loss, provided the nozzle is used as intended (air service), the thread and connections are properly installed (M12x1.25), and the tube dimensions (5 mm dia., appropriate length choice) are compatible with the system. Exceeding the stated pressure, temperature range, or exposing the nickel-plated brass to incompatible fluids or mechanical damage may reduce performance or life.

What cleaning and maintenance are recommended for the Extended straight nozzle, nickel-plated brass, series 105 to ensure longevity?

Recommended cleaning and maintenance for the Extended straight nozzle, nickel-plated brass, series 105 to ensure longevity: - Regular inspection: Check the nozzle before each use for visible dirt, wear, dents or thread damage. Inspect the 3 mm hole and 5 mm tube for obstructions. - Cleaning procedure: Blow compressed air (below max 10 bar) through the nozzle from the thread end to the tip to remove loose debris. If needed, soak in warm soapy water (mild detergent) and gently brush with a soft nylon brush; avoid abrasive tools that can scratch the nickel plating. Rinse thoroughly and dry completely before use. - Removing stubborn deposits: For mineral or oily deposits use isopropyl alcohol or a mild degreaser compatible with brass and nickel plating. Apply with a soft cloth or swab; avoid strong acids, chlorides, or ammonia-based cleaners that can corrode plating. - Thread and sealing maintenance: Keep the M12x1.25 thread clean and lightly lubricated with a thin film of appropriate anti-seize or light machine oil to prevent galling and corrosion. Wipe excess lubricant to avoid attracting dirt. - Corrosion prevention: Although nickel-plated, avoid prolonged exposure to moisture, salty air, or corrosive chemicals. Store dry and protected. - Temperature and pressure limits: Never exceed 10 bar or operate outside â10Â°C to +50Â°C; thermal or overpressure stress can damage plating and brass. - Mechanical care: Avoid bending, dropping, or striking the 5 mm tube; dents can restrict the 3 mm bore and affect fit. Use correct mounting torque on the M12x1.25 fitting to prevent distortion. - Periodic functional check: Verify free airflow through the 3 mm hole and proper sealing at connections. Replace the nozzle if plating is heavily worn, threads are damaged, or internal bore cannot be cleared. Following these steps will help maintain performance and extend the service life of the Extended straight nozzle, nickel-plated brass, series 105.

Ugello diritto allungato, ottone nichelato, serie 105

Pistole ad aria, Tutti i prodotti/

Additional information

Ugello diritto allungato con foro da 3 mm per pistole ad aria, con filetto metrico M12x1,25. Diametro tubo: 5 mm. Lunghezze disponibili: 115 mm, 165 mm, 265 mm e 415 mm. Materiale: ottone nichelato. Pressione massima: 10 bar. Temperatura di esercizio: da -10°C a +50°C.

Elenco delle varianti di prodotto

Codice articolo	Nome variante prodotto	DN	BAR	Disponibilità	Azioni
EW-105K103	Ugello allungato, dritto, L=115 mm, filetto maschio M12x1,25, ottone nichelato	-	10	In stock	Richiesta
EW-105K104	Ugello prolungato, diritto, L=165 mm, GZ M12x1,25, ottone nichelato	-	10	In stock	Richiesta
EW-105K105	Ugello prolungato, diritto, L=265 mm, GZ M12x1,25, ottone nichelato	-	10	In stock	Richiesta
EW-105K107	Ugello prolungato, diritto, L=415 mm, filetto esterno M12x1,25, ottone nichelato	-	10	In stock	Richiesta

Hai bisogno di una quantità maggiore di prodotti o di un'offerta personalizzata?

Chiamaci: +39 348 811 3340 o scrivici: m.ceriani@tubes-international.com

INVIA RICHIESTA

Ugello diritto allungato con foro da 3 mm per pistole ad aria, con filetto metrico M12x1,25. Diametro tubo: 5 mm. Lunghezze disponibili: 115 mm, 165 mm, 265 mm e 415 mm. Materiale: ottone nichelato. Pressione massima: 10 bar. Temperatura di esercizio: da -10°C a +50°C.