Is the OBHN hose collet, stainless steel clamp sleeve compatible with Teflon brake hose and resistant to corrosion in automotive environments?

The OBHN hose collet, stainless steel clamp sleeve is designed for OBHN type Teflon brake hose and, given its stainless steel construction, is compatible with Teflon-lined brake hoses and offers good corrosion resistance in automotive environments. Stainless steel resists rust and many forms of corrosion typically encountered in vehicles (moisture, road salt, oils), making it a suitable material for brake-system fittings. Compatibility notes: ensure the sleeve dimensions match the specific OBHN Teflon hose size and that proper installation torque and assembly procedures are followed to maintain a secure, leak-free connection.

Does the OBHN hose collet, stainless steel clamp sleeve fit standard Teflon brake hose sizes?

Yes. The OBHN hose collet, stainless steel clamp sleeve is designed specifically for OBHN type Teflon brake hose and will fit standard Teflon brake hose outer diameters used with that style. Made of stainless steel, it clamps the hose jacket reliably and is compatible with typical Teflon-lined brake hose dimensions specified for OBHN fittings. Ensure you match the sleeve size to your hose nominal size to guarantee proper fit and sealing.

How do I install the OBHN hose collet, stainless steel clamp sleeve on a Teflon brake hose?

To install the OBHN hose collet, stainless steel clamp sleeve on a Teflon brake hose, follow these steps: 1. Prepare tools and parts: clean workspace, OBHN hose collet, stainless steel clamp sleeve, appropriate sized ferrule or fitting, cutting tool, deburring tool, and lubricant if specified by manufacturer. 2. Cut hose square: cut the Teflon brake hose to the required length with a sharp cutter designed for PTFE/Teflon to ensure a clean, square end. Remove any loose particles and burrs with a deburring tool. 3. Slide sleeve onto hose: slide the OBHN hose collet, stainless steel clamp sleeve over the hose end with the open side toward the cut end. Ensure the sleeve sits straight and fully over the outer braid (if present) and covers the hose outer surface where the connection will be made. 4. Insert fitting/ferrule: insert the male fitting or ferrule into the hose end until it seats fully. For PTFE inner liners, confirm the inner liner is flush with the fitting shoulder or slightly recessed as recommended by the hose/fitting manufacturer. 5. Position the sleeve: slide the OBHN hose collet, stainless steel clamp sleeve forward so it covers the junction between hose braid/outer and the fitting body or ferrule. The sleeve should align evenly around the circumference with no gaps. 6. Secure the sleeve: depending on the sleeve design, crimp or clamp the OBHN hose collet, stainless steel clamp sleeve using the correct tooling (specified crimping tool or torque for clamps). Apply even pressure to compress the sleeve onto the hose and fitting, creating a tight mechanical seal. Follow manufacturer crimp dimensions or torque values to avoid under- or over-compression. 7. Inspect the assembly: check that the sleeve is centered, uniformly compressed, and there are no deformations of the Teflon liner or misalignment. Verify the fitting is firmly seated and there is no exposed braid or loose material. 8. Pressure test: perform a pressure/leak test according to application standards to confirm a secure, leak-free connection. Note: Always follow specific manufacturer installation instructions for the OBHN hose collet, stainless steel clamp sleeve and the particular Teflon hose and fittings you are using. If unsure, consult technical documentation or a qualified technician.

Boccola per tubo flessibile OBHN, acciaio inox

Tubi e raccordi per freni, Tutti i prodotti/

Additional information

Materiale	SS – acciaio inox

Boccola di serraggio per tubo freno in Teflon tipo OBHN. Materiale: acciaio inox.

Elenco delle varianti di prodotto

Codice articolo	Nome variante prodotto	DN	BAR	Disponibilità	Prezzo	Quantità	Azioni	Catalogo
RK-CAP-001N-SS	Bussola per tubo OBHN, acciaio inox	10	-	In stock	0 zł		Richiesta

Hai bisogno di una quantità maggiore di prodotti o di un'offerta personalizzata?

Chiamaci: +39 348 811 3340 o scrivici: m.ceriani@tubes-international.com

INVIA RICHIESTA

Boccola di serraggio per tubo freno in Teflon tipo OBHN. Materiale: acciaio inox.

Additional information

Materiale	SS – acciaio inox

Hai bisogno di una quantità maggiore di prodotti o di un'offerta personalizzata?

Chiamaci: +39 348 811 3340 o scrivici: m.ceriani@tubes-international.com

INVIA RICHIESTA

Rete di vendita
Verifica

Richiesta
Invia

Prodotti correlati

Potrtai nelbuje per un'offerta disponibile per questo prodotto opure non elineato?

Chiamaci: +39 348 811 3340 o scrivici: m.ceriani@tubes-international.com

INVIA RICHIESTA

TUBI E RACCORDI PER L'INDUSTRIA

Boccola per tubo flessibile OBHN, acciaio inox

Additional information

Elenco delle varianti di prodotto

Hai bisogno di una quantità maggiore di prodotti o di un'offerta personalizzata?

Additional information

Hai bisogno di una quantità maggiore di prodotti o di un'offerta personalizzata?

Prodotti correlati

Attacco pressato con GZ, tipo MALP, acciaio al carbonio

Terminale crimpatato BANJO 15°, acciaio al carbonio

Terminale pressato con filettatura interna e dado, tipo FAGP, acciaio al carbonio

Potrtai nelbuje per un'offerta disponibile per questo prodotto opure non elineato?

Prodotti

Servizi

Contatti

Social Media

Trova il tubo o raccordo perfetto per il tuo impianto

Trova il tubo o raccordo perfetto per il tuo impianto

oppure clicca per vedere tutti i nostri prodotti

Scopri anche i prodotti più richiesti, già testati sul campo