Is the BURGACLIP stainless steel clamp for hose end type 3090 compatible with automotive air conditioning hoses and refrigerants?

The BURGACLIP clamp for hose end type 3090 is designed for air-conditioning applications and is compatible with automotive A/C hoses and refrigerants when those hoses match the clampâs intended use and dimensions. Key points: - Application: The BURGACLIP clamp type 3090 is specified for air-conditioning hose ends, so it is suitable for HVAC/R systems including automotive A/C if fitted to the correct hose type. - Materials and corrosion resistance: Made from stainless steel, the BURGACLIP clamp offers corrosion resistance appropriate for automotive environments and refrigerant oils. - Sealing and pressure: Compatibility depends on the hose construction (material, reinforcement, and pressure rating) and the systemâs operating pressure. The clamp secures the hose onto a fitting; it does not change the hoseâs rated temperature/pressure or chemical compatibility with specific refrigerants. - Refrigerant compatibility: The clamp itself is indifferent to refrigerant type (R134a, R1234yf, R404A, etc.), but the overall suitability depends on hose and seal materials rated for the specific refrigerant and compressor oil. - Proper installation: Correct placement, torque, and use on the intended hose end/profile are essential for a leak-free, safe connection. Conclusion: The BURGACLIP clamp for hose end type 3090 can be used with automotive air-conditioning hoses and refrigerants provided the hose and fittings are compatible with the vehicleâs refrigerant and pressure requirements and the clamp is installed correctly.

Can the BURGACLIP clamp 3090 withstand high-pressure conditions in air conditioning systems?

Yes. The BURGACLIP clamp 3090 is designed for air conditioning hose ends and is made of stainless steel to resist corrosion and maintain clamping force under thermal and pressure cycles typical in A/C systems. Its construction provides a secure, uniform seal around flexible hoses, reducing the risk of leaks under high internal pressures encountered in refrigeration and automotive A/C. However, actual pressure resistance depends on correct clamp size, proper installation (even tightening and correct position on the hose), hose material and reinforcement, and system specifications. For critical or extreme high-pressure applications, verify the required pressure rating with BURGACLIP technical data or supplier to ensure suitability.

How do I install the BURGACLIP clamp 3090 on air conditioning hose ends safely?

To install the BURGACLIP clamp 3090 on air conditioning hose ends safely, follow these steps: 1. Prepare work area and tools: - Work in a well-ventilated, clean area. - Use protective gloves and eye protection. - Required tools: appropriate-sized screwdriver or nut driver for the clamp screw, hose cutter or sharp utility knife, and a soft-jaw plier if needed. 2. Inspect hose and fittings: - Ensure hose end and metal fitting (spigot) are clean, dry and free from corrosion, oil, or debris. - Check hose for damage; replace if cracked or hardened. - Verify correct clamp size: BURGACLIP clamp 3090 must match hose outer diameter. 3. Position the clamp: - Slide the BURGACLIP clamp 3090 over the hose before fitting the hose onto the AC fitting. - Push the hose fully onto the fitting until it seats against the fitting shoulder or stop. 4. Place clamp correctly: - Move the BURGACLIP clamp 3090 into position over the hose, centered over the barbed section or ferrule area of the fitting per manufacturer guidanceâtypically 2â5 mm from the hose end but covering the barbs completely. - Ensure the clamp band lies flat, not twisted, and the screw housing is accessible for tightening. 5. Tighten safely and evenly: - Using the correct screwdriver/nut driver, tighten the screw slowly and steadily. - Do not overtighten: tighten until the clamp compresses the hose securely without deforming or cutting it. Typical torque depends on hose material; if manufacturer torque spec is unavailable, tighten until snug plus a small additional turn, checking hose compression. - Rotate the clamp slightly and recheck tightness to ensure even seating. 6. Final checks: - Inspect the clamp seating: band flush against hose, no pinching or gaps. - Check that the hose outlet remains unobstructed and fitting alignment is correct. - If used on pressurized refrigerant lines, perform a leak test (pressure or vacuum) per refrigeration safety procedures and local regulations. - Re-torque after initial service run if recommended. Safety notes: - Never use damaged clamps; replace if bent or corroded. - Avoid sharp edges that could cut the hose when positioning the clamp. - Follow refrigerant-handling safety: recover refrigerant before disconnecting lines, and work certified if required. Using these steps with the BURGACLIP clamp 3090 ensures a secure, leak-resistant hose connection without damaging the hose or fitting.

Fascetta BURGACLIP

Tubi e raccordi per condizionamento, Tutti i prodotti/

Additional information

Materiale	SS – acciaio inox

Fascetta BURGACLIP in acciaio inox per estremità tubo tipo 3090 per climatizzazione.

Elenco delle varianti di prodotto

Codice articolo	Nome variante prodotto	DN	BAR	Disponibilità	Azioni
BU-8768-06	Fascetta BC per tubo flessibile 5/16"	-	-	In stock	Richiesta
BU-8768-08	Fascetta BC per tubo 13/32	-	-	In stock	Richiesta
BU-8768-10	Fascetta BC per tubo flessibile da 1/2"	-	-	In stock	Richiesta
BU-8768-12	Fascetta BC per tubo 5/8"	-	-	In stock	Richiesta

Hai bisogno di una quantità maggiore di prodotti o di un'offerta personalizzata?

Chiamaci: +39 348 811 3340 o scrivici: m.ceriani@tubes-international.com

INVIA RICHIESTA

Fascetta BURGACLIP in acciaio inox per estremità tubo tipo 3090 per climatizzazione.

Additional information

Materiale	SS – acciaio inox

Hai bisogno di una quantità maggiore di prodotti o di un'offerta personalizzata?

Chiamaci: +39 348 811 3340 o scrivici: m.ceriani@tubes-international.com

INVIA RICHIESTA

Rete di vendita
Verifica

Richiesta
Invia

Prodotti correlati

Potrtai nelbuje per un'offerta disponibile per questo prodotto opure non elineato?

Chiamaci: +39 348 811 3340 o scrivici: m.ceriani@tubes-international.com

INVIA RICHIESTA

TUBI E RACCORDI PER L'INDUSTRIA

Fascetta BURGACLIP

Additional information

Elenco delle varianti di prodotto

Hai bisogno di una quantità maggiore di prodotti o di un'offerta personalizzata?

Additional information

Hai bisogno di una quantità maggiore di prodotti o di un'offerta personalizzata?

Prodotti correlati

Terminale tubolare BURGACLIP senza dado, acciaio, tipo 54724

Raccordo diritto con boccola, acciaio al carbonio, tipo FR101

Terminale tubolare BURGACLIP 90° con filettatura interna UNF, acciaio, tipo 54706

Potrtai nelbuje per un'offerta disponibile per questo prodotto opure non elineato?

Prodotti

Servizi

Contatti

Social Media

Trova il tubo o raccordo perfetto per il tuo impianto

Trova il tubo o raccordo perfetto per il tuo impianto

oppure clicca per vedere tutti i nostri prodotti

Scopri anche i prodotti più richiesti, già testati sul campo