Is the DIN 20034 hose end without nut, galvanized cast iron suitable for pneumatic hoses at 16 bar without a protective flange?

Yes . the DIN 20034 hose end without nut, galvanized cast iron described ("Conical end with 'tail' for pneumatic hoses, without a protective flange. Material: galvanized cast iron. Working pressure: 16 bar.") is suitable for pneumatic hoses at 16 bar, with important caveats. Why it is suitable: - Working pressure matches: the part is rated for 16 bar, so it can handle the stated pneumatic system pressure. - Conical tail design: intended for insertion into flexible pneumatic hoses and allows hose clamping (e.g., with clamps or crimp ferrules) to secure the connection. Caveats and precautions: - No protective flange: without a flange, the connection relies entirely on a proper hose clamp or crimp sleeve. For high-pressure dynamic pneumatic systems, a mechanical clamp or crimping appropriate to hose type and pressure is essential to prevent blow-off. - Hose compatibility: ensure hose inner diameter matches the tail dimensions and that the hose reinforcement (braid, textile) is rated for 16 bar plus safety margin. - Material considerations: galvanized cast iron is corrosion-resistant but brittle compared with ductile materials; avoid excessive bending, impact, or torque that could crack the fitting. - Safety margin and standards: verify compliance with application standards and consider adding a protective flange or a coupling with mechanical retention if vibration, frequent pressure spikes, or safety regulations require it. Conclusion: The DIN 20034 hose end without nut, galvanized cast iron can be used for pneumatic hoses at 16 bar if fitted with the correct hose/clamp or crimp method and the hose and installation meet safety and application requirements.

Can DIN 20034 hose end without nut, galvanized cast iron handle 16 bar pneumatic service without a protective flange?

Yes. DIN 20034 hose end without nut, galvanized cast iron Format described as "Conical end with 'tail' for pneumatic hoses, without a protective flange. Material: galvanized cast iron. Working pressure: 16 bar." is intended for pneumatic service and specifically listed as without a protective flange, so it can be used without one provided the application limits (16 bar) and compatibility with the hose and coupling are met. Ensure proper hose fit, clamping or crimping method, and that system safety/regulatory requirements do not mandate a protective flange for your installation.

Can DIN 20034 hose end without nut, galvanized cast iron be used for pneumatic hoses at 16 bar without protective flange?

No. DIN 20034 hose end without nut, galvanized cast iron, as described (âConical end with 'tail' for pneumatic hoses, without a protective flange. Material: galvanized cast iron. Working pressure: 16 bar.â) should not be used for pneumatic hoses at 16 bar without a protective flange in typical safety-conscious installations. Why: - The part is specified with a working pressure of 16 bar, but absence of a protective flange means the hose-to-tail connection relies solely on the hose cover and a clamp/crimp over the conical tail. For pneumatic systems at 16 bar dynamic loads, vibration, and pressure spikes, a protective flange or suitable mechanical restraint is commonly required to prevent hose blow-off. - Galvanized cast iron is brittle compared with ductile fittings (e.g., forged steel or ductile iron); it can crack under shock or impact, increasing risk at high pressures. - Standards and best practice: pneumatic hose assemblies at or near 16 bar typically require end fittings and retention devices rated for the application, and manufacturers often mandate protective flanges or captive nuts to ensure secure retention. Using a tail-only, flange-less fitting may not meet those requirements or the hose manufacturerâs recommended assembly method. - Safety margin: Listed âworking pressureâ does not equal guaranteed safe use in all configurations. Without explicit certification or manufacturer instruction confirming that this specific DIN 20034 hose end can be used flange-less at 16 bar with the chosen hose, the safe choice is to use a protective flange or an alternative fitting designed and certified for flange-less use at that pressure. Recommendation: Consult the hose and fitting manufacturersâ technical data and assembly instructions. If documentation does not explicitly permit flange-less use at 16 bar with the chosen hose type and clamp/crimp method, use a protective flange or a certified alternative fitting rated for pneumatic service at 16 bar.

Attacco per tubo DIN 20034 senza dado, ghisa zincata

Raccordi e adattatori a bassa pressione, Tutti i prodotti/

Additional information

Materiale	CS – acciaio (ghisa)

Estremità conica con “codolo” per tubi pneumatici, senza flangia di protezione. Materiale: ghisa zincata. Pressione di esercizio: 16 bar.

Elenco delle varianti di prodotto

Codice articolo	Nome variante prodotto	DN	BAR	Disponibilità	Prezzo	Quantità	Azioni	Catalogo
MU-1906	Raccordo terminale DIN 20034 DN15 per tubo 3/4", acciaio zincato	20	16	In stock	0 zł		Richiesta

Hai bisogno di una quantità maggiore di prodotti o di un'offerta personalizzata?

Chiamaci: +39 348 811 3340 o scrivici: m.ceriani@tubes-international.com

INVIA RICHIESTA

Estremità conica con “codolo” per tubi pneumatici, senza flangia di protezione. Materiale: ghisa zincata. Pressione di esercizio: 16 bar.

Additional information

Materiale	CS – acciaio (ghisa)

Hai bisogno di una quantità maggiore di prodotti o di un'offerta personalizzata?

Chiamaci: +39 348 811 3340 o scrivici: m.ceriani@tubes-international.com

INVIA RICHIESTA

Rete di vendita
Verifica

Richiesta
Invia

Prodotti correlati

Potrtai nelbuje per un'offerta disponibile per questo prodotto opure non elineato?

Chiamaci: +39 348 811 3340 o scrivici: m.ceriani@tubes-international.com

INVIA RICHIESTA

TUBI E RACCORDI PER L'INDUSTRIA

Attacco per tubo DIN 20034 senza dado, ghisa zincata

Additional information

Elenco delle varianti di prodotto

Hai bisogno di una quantità maggiore di prodotti o di un'offerta personalizzata?

Additional information

Hai bisogno di una quantità maggiore di prodotti o di un'offerta personalizzata?

Prodotti correlati

Estremità a “T” con filetto maschio BSPT, poliammide

Raccordo terminale femmina BSP, dado esagonale, per tubo, ottone, tipo NiTO A

Raccordo dritto, copolimero acetalico

Potrtai nelbuje per un'offerta disponibile per questo prodotto opure non elineato?

Prodotti

Servizi

Contatti

Social Media

Trova il tubo o raccordo perfetto per il tuo impianto

Trova il tubo o raccordo perfetto per il tuo impianto

oppure clicca per vedere tutti i nostri prodotti

Scopri anche i prodotti più richiesti, già testati sul campo