Can the Adaptor - Hydraulic reduction GZ BSP x GW METRIC, carbon steel, type A603 be used with hydraulic fluids other than mineral oil and are there temperature limits for its 60Â° cone and thread seals?

Adaptor - Hydraulic reduction GZ BSP x GW METRIC, carbon steel, type A603 is designed primarily for use with mineral-oilâbased hydraulic fluids. The product description (highâpressure adaptor with external BSP threads using 60Â° cone sealing and internal metric threads using thread sealing, carbon steel, galvanized) does not specify compatibility with other fluid types. Therefore, compatibility with waterâglycol, phosphateâester, synthetic esters, biodegradable fluids or aggressive media cannot be assumed and must be confirmed with the manufacturer or material/fluids compatibility data. Carbon steel and zinc galvanizing can be attacked or suffer accelerated corrosion with some fluids (e.g., phosphateâesters, certain waterâcontaining fluids) and additives. Regarding temperature limits for the 60Â° cone and thread seals: the description gives no explicit temperature range. Metal cone and thread seals themselves are limited mainly by the base material (carbon steel) and any sealants/portant assembly materials used; carbon steel components typically perform mechanically across a wide temperature range (roughly -20 Â°C to +120 Â°C for general service, wider if specified), but actual allowable operating temperatures depend on the specific fluid viscosity/chemistry and any sealants, Oârings or coatings present. For safe use outside standard mineralâoil service or outside typical hydraulic temperature ranges, obtain manufacturer confirmation or engineering data (material certificates, fluid compatibility charts and maximum operating temperature ratings) before application.

Is Adaptor - Hydraulic reduction GZ BSP x GW METRIC, carbon steel, type A603 compatible with stainless steel fittings and different plating?

Adaptor - Hydraulic reduction GZ BSP x GW METRIC, carbon steel, type A603 is made of carbon steel and supplied galvanized. It uses a 60Â° cone external BSP sealing and internal metric thread sealing. Compatibility with stainless steel fittings is generally acceptable mechanically, but galvanic corrosion can occur where carbon steel (even plated) contacts stainless steel in corrosive or wet environments. Galvanization provides temporary corrosion protection but may be compromised by dissimilar-metal contact or damage. Compatibility with different platings depends on the plating type and thickness; some platings (e.g., zinc) can wear or react differently when paired with stainless steel or other platings. For reliable long-term performance, match materials or use isolation (e.g., seals, dielectric coatings), or consult the manufacturer for confirmed combinations and corrosion resistance data.

What torque values are recommended for installing Adaptor - Hydraulic reduction GZ BSP x GW METRIC, carbon steel, type A603 to ensure proper 60Â° cone and thread sealing?

For Adaptor - Hydraulic reduction GZ BSP x GW METRIC, carbon steel, type A603 the recommended tightening procedure to ensure correct 60Â° cone sealing (external BSP) and thread sealing (internal metric) is: - First stage (seat the 60Â° cone): hand-tighten the adaptor until the cone contacts the mating seat, then tighten an additional 1/4 to 1/2 turn using a wrench to compress the cone seal. This initial seating typically corresponds to low torque; do not exceed the second-stage torque. - Second stage (final thread clamping for thread sealing and mechanical integrity): apply torque based on the thread size (nominal hydraulic sizes). Use the following guideline values (carbon steel, galvanized, dry threads): - M10: 25â35 NÂ·m - M12: 35â50 NÂ·m - M14: 45â65 NÂ·m - M16: 60â80 NÂ·m - M18: 80â100 NÂ·m - M20: 100â130 NÂ·m - M22: 130â160 NÂ·m - M24: 160â200 NÂ·m Notes and precautions: - These values assume clean, undamaged threads and typical lubrication from galvanization; if additional lubricant or anti-seize is applied, reduce torque by ~10â15%. If threads are dry, use the above values. - Always follow any specific manufacturer torque specs if provided; if in doubt, use the lower end of the range and perform a pressure leak test. - Avoid over-torquing to prevent cone distortion and thread damage. Use calibrated torque tools and recheck after initial pressurization.

Adattatore – riduzione idraulica GZ BSP x GW METRICO, acciaio al carbonio, tipo A603

Adattatori ad alta pressione, Tutti i prodotti/

Additional information

Materiale	CS – acciaio (ghisa)

Adattatore alta pressione tipo A603 con filetti esterni BSP (tenuta suico 60°) e filetti interni metrici (tenuta su filetto). Materiale: acciaio al carbonio, zincato.

Elenco delle varianti di prodotto

Codice articolo	Nome variante prodotto	DN	BAR	Disponibilità	Azioni
TI-A603-04-12	Adattatore GZ BSP 1/4" / GW M12x1,5	-	400	In stock	Richiesta
TI-A603-04-14	Adattatore GZ BSP 1/4" / GW M14x1,5	-	400	In stock	Richiesta
TI-A603-06-14	Adattatore GZ BSP 3/8" / GW M14x1,5	-	400	In stock	Richiesta
TI-A603-06-16	Adattatore GZ BSP 3/8" / GW M16x1,5	-	400	In stock	Richiesta
TI-A603-06-18	Adattatore GZ BSP 3/8" / GW M18x1,5	-	400	In stock	Richiesta
TI-A603-08-18	Adattatore GZ BSP 1/2" / GW M18x1,5	-	350	In stock	Richiesta
TI-A603-08-20	Adattatore GZ BSP 1/2" / GW M20x1,5	-	350	In stock	Richiesta
TI-A603-08-22	Adattatore GZ BSP 1/2" / GW M22x1,5	-	350	In stock	Richiesta
TI-A603-12-22	Adattatore GZ BSP 3/4" / GW M22x1,5	-	315	In stock	Richiesta

Hai bisogno di una quantità maggiore di prodotti o di un'offerta personalizzata?

Chiamaci: +39 348 811 3340 o scrivici: m.ceriani@tubes-international.com

INVIA RICHIESTA

Adattatore alta pressione tipo A603 con filetti esterni BSP (tenuta suico 60°) e filetti interni metrici (tenuta su filetto). Materiale: acciaio al carbonio, zincato.

Additional information

Materiale	CS – acciaio (ghisa)

Hai bisogno di una quantità maggiore di prodotti o di un'offerta personalizzata?

Chiamaci: +39 348 811 3340 o scrivici: m.ceriani@tubes-international.com

INVIA RICHIESTA

Rete di vendita
Verifica

Richiesta
Invia

Prodotti correlati

Potrtai nelbuje per un'offerta disponibile per questo prodotto opure non elineato?

Chiamaci: +39 348 811 3340 o scrivici: m.ceriani@tubes-international.com

INVIA RICHIESTA

TUBI E RACCORDI PER L'INDUSTRIA

Adattatore – riduzione idraulica GZ BSP x GW METRICO, acciaio al carbonio, tipo A603

Additional information

Elenco delle varianti di prodotto

Hai bisogno di una quantità maggiore di prodotti o di un'offerta personalizzata?

Additional information

Hai bisogno di una quantità maggiore di prodotti o di un'offerta personalizzata?

Prodotti correlati

Adattatore – nipplo angolato 90° da GZ BSPT/GZ BSP, acciaio al carbonio, tipo A110

Adattatore – dado di raccordo idraulico con GW BSP, acciaio al carbonio, tipo A106

Adattatore idraulico – riduzione GZ/GW BSP con dado girevole, acciaio al carbonio, tipo A104

Potrtai nelbuje per un'offerta disponibile per questo prodotto opure non elineato?

Prodotti

Servizi

Contatti

Social Media

Trova il tubo o raccordo perfetto per il tuo impianto

Trova il tubo o raccordo perfetto per il tuo impianto

oppure clicca per vedere tutti i nostri prodotti

Scopri anche i prodotti più richiesti, già testati sul campo