Is the Collet for hydraulic hoses 4SH, R12, carbon steel, type M4X compatible with external machining installation and which D1/D3 tolerances are required?

Yes. Collet for hydraulic hoses 4SH, R12, carbon steel, type M4X is compatible with external machining installation . the product description explicitly states "Installation - external machining." For proper fit, use the following dimensional guidance derived from the listed parameters: - D1 (outer diameter): match the hose outer diameter specified for 4SH/R12 construction; the colletâs D1 must correspond to the hose outer diameter to ensure correct seating. Typical 4SH/R12 hose outer diameters vary by size, so select the collet size where D1 equals the hose OD (manufacturerâs hose datasheet). - D3 (lock diameter): use the colletâs lock diameter clearance as specified for the matching coupling; D3 must engage the couplingâs groove or sealing surface per the coupling makerâs tolerance band. Ensure D3 is within the coupling supplierâs recommended lock diameter tolerance (typically a close tolerance fit, e.g., h7/g6 class equivalents) to guarantee secure locking and prevent slippage. Material note: carbon steel, galvanized finish requires common machining allowances and corrosion protection; follow supplier torque and assembly instructions. If exact numeric tolerances are required, obtain the specific D1/D3 values and tolerance classes from the collet/coupling manufacturer or technical drawing for the selected nominal hose size.

What torque and tightening sequence are recommended for Collet for hydraulic hoses 4SH, R12, carbon steel, type M4X during external machining installation?

Collet for hydraulic hoses 4SH, R12, carbon steel, type M4X Format Recommended tightening torque and sequence for external machining installation: - Tightening torque: 20â30 Nm (apply incrementally; start at ~10 Nm, then 20 Nm, finish at target). For precise fit verify with manufacturerâs spec if available; if hose assembly includes sealing elements, use lower end of range. - Tightening sequence: tighten bolts in a criss-cross/star pattern evenly around the clamp sleeve to ensure uniform compression of D1 (outer diameter) onto D3 (lock diameter). Perform 2â3 passes, increasing torque each pass. After pressure testing, recheck torque and retighten to specified value if necessary.

Can Collet for hydraulic hoses 4SH, R12, carbon steel, type M4X require specific surface finish or concentricity for external machining installation?

Collet for hydraulic hoses 4SH, R12, carbon steel, type M4X may require specific surface finish and concentricity for proper external machining installation to ensure sealing, clamp reliability and ease of assembly. Based on the M4X clamp sleeve description (external machining installation, D1 = outer diameter, D3 = lock diameter, material carbon steel, galvanized), key considerations: - Surface finish: The external mating surfaces (outer diameter D1 and lock diameter D3) should be free of heavy burrs, deep scratches or machining marks that could impede seating or damage the hose cover. A moderate machined finish (e.g., Ra in a typical machined range, such as 0.8â3.2 Î¼m) is usually acceptable for clamp sleeves on rubber hydraulic hoses, but finer finishes may improve seal contact and reduce risk of abrasive wear on hose covers. Galvanized coating adds corrosion protection but can affect thickness and local fitâensure coating uniformity. - Concentricity: Concentricity between the inner bore (where the hose fits) and the external diameters D1/D3 is important to ensure even clamping pressure and correct engagement of the lock features during external machining installation. Excessive eccentricity can cause uneven clamping, local stress on the hose cover or reinforcement, and potential leakage or premature wear. Typical industrial practice calls for concentricity within suitable tolerances for hose fittings (often a few hundred microns), but exact values depend on hose and assembly requirements. - Dimensional controls: Maintain specified D1 and D3 within tolerance so the sleeve mates correctly with mating components and locking mechanism. Control of roundness and cylindricity in the critical diameters supports reliable installation. - Surface protection and post-machining treatment: After external machining, remove sharp edges and protect the galvanized coating where necessary; re-galvanizing or passivation may be required if coating is damaged. In summary, while exact numeric tolerances depend on application and supplier specifications, ensure smooth, burr-free machined surfaces and good concentricity between bore and external diameters to achieve proper installation and reliable performance of Collet for hydraulic hoses 4SH, R12, carbon steel, type M4X.

Boccola per tubi idraulici 4SH, R12, acciaio al carbonio, tipo M4X

Additional information

Materiale	CS – acciaio (ghisa)

Boccola di serraggio M4X per tubi idraulici in gomma tipo 4SH o R12. Installazione – lavorazione esterna. Diametro D1 [mm] – diametro esterno. Diametro D3 [mm] – diametro di bloccaggio. Materiale: acciaio al carbonio, zincato.

Elenco delle varianti di prodotto

Codice articolo	Nome variante prodotto	DN	BAR	Disponibilità	Azioni
TI-M4X-20	Ghiera per tubi idraulici 4SH 1.1/4"	32	-	In stock	Richiesta
TI-M4X-24	Manicotto per tubi idraulici 4SH 1.1/2"	38	-	In stock	Richiesta
TI-M4X-32	Boccola per tubi idraulici 4SH/R12 2"	50	-	In stock	Richiesta

Hai bisogno di una quantità maggiore di prodotti o di un'offerta personalizzata?

Chiamaci: +39 348 811 3340 o scrivici: m.ceriani@tubes-international.com

INVIA RICHIESTA

Boccola di serraggio M4X per tubi idraulici in gomma tipo 4SH o R12. Installazione – lavorazione esterna. Diametro D1 [mm] – diametro esterno. Diametro D3 [mm] – diametro di bloccaggio. Materiale: acciaio al carbonio, zincato.

Additional information

Materiale	CS – acciaio (ghisa)

Hai bisogno di una quantità maggiore di prodotti o di un'offerta personalizzata?

Chiamaci: +39 348 811 3340 o scrivici: m.ceriani@tubes-international.com

INVIA RICHIESTA

Rete di vendita
Verifica

Richiesta
Invia

Prodotti correlati

Potrtai nelbuje per un'offerta disponibile per questo prodotto opure non elineato?

Chiamaci: +39 348 811 3340 o scrivici: m.ceriani@tubes-international.com

INVIA RICHIESTA

TUBI E RACCORDI PER L'INDUSTRIA

Boccola per tubi idraulici 4SH, R12, acciaio al carbonio, tipo M4X

Additional information

Elenco delle varianti di prodotto

Hai bisogno di una quantità maggiore di prodotti o di un'offerta personalizzata?

Additional information

Hai bisogno di una quantità maggiore di prodotti o di un'offerta personalizzata?

Prodotti correlati

Boccola per tubi idraulici 4SH, R13, R15, acciaio al carbonio, tipo IL4

Raccordo idraulico DKR 90°, tipo ZBW410 – COMPACT, acciaio al carbonio

Raccordo INTERLOCK diritto con filetto interno BSP, acciaio al carbonio

Potrtai nelbuje per un'offerta disponibile per questo prodotto opure non elineato?

Prodotti

Servizi

Contatti

Social Media

Trova il tubo o raccordo perfetto per il tuo impianto

Trova il tubo o raccordo perfetto per il tuo impianto

oppure clicca per vedere tutti i nostri prodotti

Scopri anche i prodotti più richiesti, già testati sul campo